top of page

ACTFLEX CRACK LOCK E400L

​

Ultra-Low Viscosity | 80.5 MPa Compressive | Self-Levelling

Structural injection epoxy that wicks deep into hairline cracks and restores structural continuity from within.

At 100–500 cps, CRACKLOCK E400L reaches cracks from 0.05 mm to 3 mm wide that paste-grade adhesives cannot enter, filling horizontal cracks by gravity feed and vertical cracks by port injection. Typical R&D values of 70.3 MPa flexural and 34.6 MPa tensile strength, with just 0.01% shrinkage on cure, give a repair that holds its section. The 100% solids, solvent-free formulation also serves as an epoxy mortar binder and, with aggregate, for interior overlays. It suits warehouses, bridges, tunnels and infrastructure repairs. Supplied in 400 mL dual cartridges at 3:1 by volume. Not a waterproofing membrane; dry substrates only, maximum 3 mm crack width.

specs

Technical Specifications.

Waterproof Time:

​

Coverage:

Crack dependent: approx. 40 m per 400 mL cartridge at 1 × 10 mm crack (0.05–3 mm width range)

Usable period after opening:

Gel time: 30–40 min

Touch dry time minimum:

Tack-free: 3–5 h

Vapour Pressure @ 25°C:

​

Application Temperature:

5°C – 35°C

Shelf Life:

24 months unopened

Membrane
Classification:

​

Colour:

Clear to light amber

Tack Free Time:

3–5 h

Recoat Time:

24 hours before coating with paint or architectural coatings

Elongation at Break:

​

Recommended
Thickness:

Prepared groove: 3 mm width, minimum 1 mm depth.

Chemical
Resistant:

​

Full Cure:

7 days at 24°C

Chemical Base:

100% Solids Epoxy (Solvent-Free)

Cure Mechanism:

Chemical reaction – 3:1 mix ratio

Tear Propagation
Resistance:

​

Service
Temperature:

-7°C to +50°C (after curing)

Solids Content:

100%

Bond Strength:

​

Density:

​

Compressive
Strength:

80.5 MPa (ASTM D695-15)

Flow:

80.5 MPa (ASTM D695-15)

Acceptance of Cyclic Movement:

​

Dimensional Stability:

​

Control Elongation at Break:

​

Control Tensile Strength:

34.6 MPa (ASTM D638-14)

Water Immersion Elongation at Break:

​

Water Immersion Tensile Strength:

​

Detergent Immersion Elongation at Break:

​

Detergent Immersion Tensile Strength:

​

Heat Aging Elongation at Break:

​

Heat Aging Tensile Strength:

​

Field Seam Strength:

​

Temperature Resistance:
Water Vapour Transmission

​

Water Vapour Transmission:

​

Application Method:

​

VOC Content:

​

Mixing Ratio:

3:1, Part A to Part B

Viscosity:

100–500 cps at 25°C

Storage Temperature:

​

Flash Point:

​

UV Resistance:

​

Hydrostatic Pressure Resistance:

​

Water Vapour Transmission Rate (WVTR):

​

Abrasion Resistance:

​

Bacterial/Algae Resistance:

​

Application Time:

​

Environmental Impact:

​

Packaging Sizes:

​

Hardness:

​

Adhesion to Substrate:

​

Appearance After Curing:

​

Clean-up Requirements:

​

Certification Standards:

​

calculator

Coverage Calculator.

100m2

Based on a manufacturers average recommended coverage of Crack dependent: approx. 40 m per 400 mL cartridge at 1 × 10 mm crack (0.05–3 mm width range)

Required:

NaN

pdfs

Product Documentation.

Technical Data Sheet (PDF Download)

Safety Data Sheet 1 (PDF Download)

Safety Data Sheet 2 (PDF Download)

Compliance Testing Report 1 (PDF Download)

Compliance Testing Report 2 (PDF Download)

Compliance Testing Report 3 (PDF Download)

Low VOC Certificate (PDF Download)

Product How To Guide (PDF Download)

Technical Drawings (PDF Download)

3d

Application Model

ACTFLEX CRACK LOCK E400L

locate

Find a Stockist Near You

Company Name

Distance

Address

Phone

ACTFLEX CRACK LOCK E400L

Available in (sizes)

400 mL dual cartridge

Need to Know More?

I am a…

Got a question about ACTFLEX CRACK LOCK E400L? Our technical team can help with specification, surface prep, coverage and compatibility.

Call (02) 8021 3517
Email info@forspec.com.au

ACTFLEX CRACK LOCK E400L GALLERY

bottom of page