(02) 8021 3517 Send your job →
● Part of the waterproofing membranes range

Sheet membranes & torch-on membranes

Factory-made sheets in four kinds: torch-on bitumen for roofs and planters, self-adhesive sheets for walls, podiums and wet areas, pre-applied sheets laid before the pour, and a hot-air welded PVC sheet. The thickness is set in the factory, not on the day.

8products
4systems
TDS+SDSwhere issued
3D drawing: FORSPEC sheet membrane laid over a concrete slab
● The whole range

All 8 sheet membranes.

TDS and SDS open straight from the card.

FORZAFLEX BASE 3MM

FORZAFLEX BASE 3MM

AS 4654.1 Class I

  • AS 4654.1 Class I
  • Torch-Fused Both Faces
  • No Cure Period
FORZAFLEX MINERALE 4.5

FORZAFLEX MINERALE 4.5

AS 4654.1 Class I

  • AS 4654.1 Class I
  • Permanent UV Protection
  • No Topcoat
FORZAFLEX RR

FORZAFLEX RR

Root Resistant

  • Root Resistant
  • AS 4654.1 Class I
  • UV-Stable Mineral Face
Main productMain
ACTFLEX 5000

ACTFLEX 5000

Non-Asphalt Polymer Resin

  • Non-Asphalt Polymer Resin
  • Peel-and-Stick
  • No Open Flame
ACTFLEX SAR

ACTFLEX SAR

Self-Adhesive Cold-Lay

  • Self-Adhesive Cold-Lay
  • No Cure Period
  • Solvent-Free
PREFLEX 3000

PREFLEX 3000

Fully Bonded

  • Fully Bonded
  • No Primers or Heat
  • Self-Protecting
ACTFLEX 5000S

ACTFLEX 5000S

Reactive Sand Bond

  • Reactive Sand Bond
  • Peel-and-Stick
  • Flexible to −25°C
ACTFLEX POLYFIN

ACTFLEX POLYFIN

AS 4654.1 Class II

  • AS 4654.1 Class II
  • Hot-Air Welded
  • Certified Trafficable
● Which sheet, where

Eight sheets, from their data sheets.

How each one goes down, its thickness, whether it can be left in the sun and what its data sheet says about its rating.

ProductHow it goes downThicknessLeft exposed?Rating on the data sheet
FORZAFLEX BASE 3MMTorched on as the base ply, under a cap sheetTorched3.0 mm3.0 mmNo: always covered by a cap sheet or protectionNoClass I, AS 4654.1 (Report 597-1)Class I, AS 4654.1 (Report 597-1)
FORZAFLEX MINERALE 4.5Torched on as the cap sheet, over the base plyTorched4.0 mm (4.5 kg/m²)4.0 mmYes: the mineral slate face is the UV protectionYesClass I, AS 4654.1 (Report 596-1)Class I, AS 4654.1 (Report 596-1)
FORZAFLEX RRTorched on as a root-resistant cap sheetTorched4.0 mm4.0 mmYes: UV stable, in the sun or under soilYesClass I, AS 4654.1 (Report 589-1)Class I, AS 4654.1 (Report 589-1)
ACTFLEX 5000Self-adhesive, with 75 mm lapsPeel and stickNot given on the data sheetNot givenNo: always covered by protectionNoClass III, AS 4654.1 (Report 373)Class III, AS 4654.1 (Report 373)
ACTFLEX SARSelf-adhesive, laid cold on a primed, dry surfacePeel and stick1.5 mm (typical)1.5 mmNo: always tiled, screeded or toppedNoMade to Class III; certification testing in progressMade to Class III; certification testing in progress
PREFLEX 3000Laid before the pour; the concrete bonds to itBefore the pour1.7 mm1.7 mmNo: cast against the structureNoClass III, AS 4654.1, typical values while the report is reissuedClass III, AS 4654.1, typical values while the report is reissued
ACTFLEX 5000SLaid before the pour; the topping slab bonds to its sand faceBefore the pourNot given on the data sheetNot givenNo: covered by the slabNoFORSPEC R&D values to GB/T 23457; no AS class givenFORSPEC R&D values to GB/T 23457; no AS class given
ACTFLEX POLYFINMechanically fastened, laps hot-air weldedWelded1.5 or 2.0 mm (Type P)1.5 or 2.0 mmYes: UV stable, for foot and occasional service vehicle trafficYesClass II, AS 4654.1 (Report 608-1)Class II, AS 4654.1 (Report 608-1)

Ratings and figures as printed on each product's current data sheet. Open the TDS from the product cards above before you specify.As printed on each data sheet. Check the TDS before you specify.

● By type

Torch-on, self-adhesive, pre-applied and welded.

● Where they are used

In 4 FORSPEC systems.

Each system page shows the full build-up these sheets sit in.

● On site

Real jobs, laid in sheet.

● 3D models

See every layer before site starts.

Each FORSPEC detail is modelled in 3D so the site team sees the build-up for sheet membranes before anyone opens a pail. Send the job and we model yours.

3D model: Pile cap tanking
Pile cap tankingSheet membrane dressed around the pile head
3D model: Planter box
Planter boxMembrane, drainage cell and outlet
3D model: Retaining wall, exploded
Retaining wall, explodedWall, membrane and drainage · layer by layer
● CAD library

Drawn details, ready for your set.

17 standard details for sheet membranes. Open one to view it and download the PDF and DXF.

● The other ranges

Seven ranges. 92 products.

● Not sure it suits the job?

Send us the job. We spec it.

Drawings, photos or a description. A FORSPEC rep comes back with the system, the spec clause, CAD details and a 3D visual within 6 business hours.

Send us your job →☎