top of page

ACTFLEX EPOXY GROUT

​

80 MPa Compressive | Pours Up To 100 mm | Solvent Free

Flowable two-part structural epoxy grout for reinstating large concrete voids and grouting baseplates and plinths.

With a mixed viscosity of 250–450 mPa·s, ACTFLEX EPOXY GROUT wets and penetrates open-textured concrete and flows beneath machine bases and bearing plates for load-transfer grouting. Typical bond to prepared concrete exceeds 2.5 MPa with failure in the concrete, and it tolerates substrate moisture up to 4% where there is no standing water. The same resin doubles as the primer for ACTFLEX HBR and the binder for approved aggregate-filled repair and heavy-duty floor systems, and grouts pile caps in the FORSPEC PREFLEX basement tanking system. Each pre-proportioned 30 kg kit yields about 28.5 L. Rigid: not for movement joints, and not a dedicated hairline crack-injection resin.

specs

Technical Specifications.

Waterproof Time:

​

Coverage:

Priming: 0.2–0.3 L/m² per coat; void filling: 1.05 kg per litre of void (one 30 kg kit fills approx. 28.5 L)

Usable period after opening:

Pot Life: 40 minutes at 25°C

Touch dry time minimum:

Initial set: 10–12 hours at 25°C

Vapour Pressure @ 25°C:

​

Application Temperature:

10°C – 35°C

Shelf Life:

24 months

Membrane
Classification:

​

Colour:

Translucent amber, mixed

Tack Free Time:

​

Recoat Time:

30–60 minutes (tacky window)

Elongation at Break:

​

Recommended
Thickness:

Maximum single-pour depth: 100 mm.

Chemical
Resistant:

Chemically resistant epoxy matrix for approved exposures; check fuels, oils, acids, alkalis and process chemicals against current FORSPEC guidance

Full Cure:

7 days at 25°C

Chemical Base:

Epoxy

Cure Mechanism:

Two-component chemical cure

Tear Propagation
Resistance:

​

Service
Temperature:

​

Solids Content:

​

Bond Strength:

>2.5 MPa (concrete failure)

Density:

~1.05 g/cm³

Compressive
Strength:

80 MPa at 7 days, 25°C

Flow:

80 MPa at 7 days, 25°C

Acceptance of Cyclic Movement:

​

Dimensional Stability:

​

Control Elongation at Break:

​

Control Tensile Strength:

35 MPa at 7 days, 25°C (neat resin casting)

Water Immersion Elongation at Break:

​

Water Immersion Tensile Strength:

​

Detergent Immersion Elongation at Break:

​

Detergent Immersion Tensile Strength:

​

Heat Aging Elongation at Break:

​

Heat Aging Tensile Strength:

​

Field Seam Strength:

​

Temperature Resistance:
Water Vapour Transmission

​

Water Vapour Transmission:

​

Application Method:

​

VOC Content:

​

Mixing Ratio:

2:1 by volume; 2:1 by weight (Part A 20 kg : Part B 10 kg)

Viscosity:

250–450 mPa·s at 25°C

Storage Temperature:

​

Flash Point:

​

UV Resistance:

​

Hydrostatic Pressure Resistance:

​

Water Vapour Transmission Rate (WVTR):

​

Abrasion Resistance:

​

Bacterial/Algae Resistance:

​

Application Time:

​

Environmental Impact:

​

Packaging Sizes:

​

Hardness:

​

Adhesion to Substrate:

​

Appearance After Curing:

​

Clean-up Requirements:

​

Certification Standards:

​

calculator

Coverage Calculator.

100m2

Based on a manufacturers average recommended coverage of Priming: 0.2–0.3 L/m² per coat; void filling: 1.05 kg per litre of void (one 30 kg kit fills approx. 28.5 L)

Required:

25 L

pdfs

Product Documentation.

Technical Data Sheet (PDF Download)

Safety Data Sheet 1 (PDF Download)

Safety Data Sheet 2 (PDF Download)

Compliance Testing Report 1 (PDF Download)

Compliance Testing Report 2 (PDF Download)

Compliance Testing Report 3 (PDF Download)

Low VOC Certificate (PDF Download)

Product How To Guide (PDF Download)

Technical Drawings (PDF Download)

3d

Application Model

ACTFLEX EPOXY GROUT

locate

Find a Stockist Near You

Company Name

Distance

Address

Phone

ACTFLEX EPOXY GROUT

Available in (sizes)

30 kg kit (Part A 20 kg + Part B 10 kg)

Need to Know More?

I am a…

Got a question about ACTFLEX EPOXY GROUT? Our technical team can help with specification, surface prep, coverage and compatibility.

Call (02) 8021 3517
Email info@forspec.com.au

ACTFLEX EPOXY GROUT GALLERY

bottom of page