FORZAFLEX RR
Root Resistant | AS 4654.1 Class I | UV-Stable Mineral Face
Torch-applied APP bitumen cap sheet for planter boxes and green roofs, protecting the waterproofing beneath soil and plants.
Anti-root additives are blended through the bitumen itself rather than applied as a surface treatment, while a high-strength polyester composite carries the mechanical load. Certified results in NATA-accredited Report 589-1 include 50 cycles of cyclic movement without rupture, retained extensibility after UV exposure, very low water vapour transmission of 0.03 g/m²/24 h and field seam strength of 286.37 N/25 mm. Because the surface can stay exposed, one sheet serves both the planted and open areas of a roof or podium, fully torch-bonded to FORZAFLEX BASE 3mm with no cure period. Root resistance is not classified under an Australian Standard. Maintenance access only, not trafficable.
specs
Technical Specifications.
Waterproof Time:
Immediate waterproofing after installation.
Coverage:
10 m² gross per roll; approx. 9.1 m² effective at 75 mm side and 150 mm end laps (approx. 11 rolls per 100 m²)
Usable period after opening:
Touch dry time minimum:
Not applicable – torch-applied membrane.
Vapour Pressure @ 25°C:
Application Temperature:
5°C to 40°C ambient
Shelf Life:
24 months from manufacture, stored as specified
Membrane
Classification:
CLASS I (low extensibility)
Colour:
Tack Free Time:
Recoat Time:
Final cap sheet layer; no further membrane overlay required. In planted areas, place protection board only after a successful flood test.
Elongation at Break:
39% control — Report 589-1
Recommended
Thickness:
4.0 mm
Chemical
Resistant:
Full Cure:
Fully bonded upon cooling.
Chemical Base:
APP Modified Bitumen
Cure Mechanism:
Torch-applied heat fusion bonding.
Tear Propagation
Resistance:
Service
Temperature:
−15°C to +85°C
Solids Content:
Bond Strength:
21.72 N to unprimed concrete — Report 589-1
Density:
Compressive
Strength:
Flow:
Acceptance of Cyclic Movement:
Pass — 50 cycles, no rupture, crazing or tears (AS 4654.1 App. B — Report 589-1)
Dimensional Stability:
No changes observed over two full cycles (ASTM D6207 — Report 589-1)
Control Elongation at Break:
Control Tensile Strength:
2.31 MPa (AS 1145.3 — Report 589-1)
Water Immersion Elongation at Break:
Water Immersion Tensile Strength:
Detergent Immersion Elongation at Break:
Detergent Immersion Tensile Strength:
Heat Aging Elongation at Break:
Heat Aging Tensile Strength:
Field Seam Strength:
286.37 N/25 mm (AMTM005 — Report 589-1)
Temperature Resistance:
Water Vapour Transmission
Water Vapour Transmission:
0.03 g/m²/24 h (ASTM E96 desiccant method — Report 589-1)
Application Method:
VOC Content:
Mixing Ratio:
Viscosity:
Storage Temperature:
Flash Point:
UV Resistance:
Fully UV stable — may be left exposed (Report 589-1)
Hydrostatic Pressure Resistance:
Water Vapour Transmission Rate (WVTR):
Abrasion Resistance:
0.539 mm (H-22 wheel, 1000 cycles) — not trafficable, maintenance access only; 0.099 mm non-trafficable (CS-10, 500 cycles) — AS 1580.403.2, Report 589-1
Bacterial/Algae Resistance:
Application Time:
Environmental Impact:
Packaging Sizes:
Hardness:
Adhesion to Substrate:
Appearance After Curing:
Clean-up Requirements:
Certification Standards:
calculator
Coverage Calculator.
Based on a manufacturers average recommended coverage of 10 m² gross per roll; approx. 9.1 m² effective at 75 mm side and 150 mm end laps (approx. 11 rolls per 100 m²)
Required:
NaN
pdfs
Product Documentation.
Safety Data Sheet 2 (PDF Download)
Compliance Testing Report 2 (PDF Download)
Compliance Testing Report 3 (PDF Download)
Low VOC Certificate (PDF Download)
Product How To Guide (PDF Download)
Technical Drawings (PDF Download)
3d
Application Model

.png)
Available in (sizes)
10m x 1m Roll
Need to Know More?
Got a question about FORZAFLEX RR? Our technical team can help with specification, surface prep, coverage and compatibility.
Call (02) 8021 3517
Email info@forspec.com.au