ACTFLEX 900R
Tile Direct, No Primer | Hot-Air Welded Laps | No Open Flame
Dual-fabric butyl rubber sheet membrane for showers, bathrooms and laundries, with a consistent factory-controlled 0.9 mm gauge.
Tiling, screeding and flood testing can all proceed sixty minutes after the final weld, so the membrane adds no cure time to a tight wet-area programme. Butyl rubber is effectively closed to water vapour, does not oxidise or embrittle with age, and keeps taking up movement at junctions and across substrate cracking, while elongation greater than 300% lets corners be dressed without fillets or bond breakers. Full-area bonding with ACTFLEX 302 ADHESIVE prevents lateral water tracking, and membrane and installation details comply with AS 3740:2021. It suits encapsulated electric underfloor heating. Internal use only, always covered by tiles, screed or a comparable finish, and installed by FORSPEC-accredited applicators.
specs
Technical Specifications.
Waterproof Time:
Coverage:
Roll gross area 28 m²; effective coverage 27.2 m² per roll (1.36 m effective width x 20 m, after 40 mm welded side lap); practical coverage approximately 25–26 m² per roll
Usable period after opening:
Touch dry time minimum:
Vapour Pressure @ 25°C:
Application Temperature:
5°C to 35°C ambient (average)
Shelf Life:
Minimum 60 months from date of manufacture in unopened original packaging; store under cover in dry conditions between 5°C and 30°C
Membrane
Classification:
Colour:
Core: butyl rubber, light grey; Fabric facing: white nonwoven fabric, both faces
Tack Free Time:
Recoat Time:
Elongation at Break:
Greater than 300% (AS/NZS 4858, typical)
Recommended
Thickness:
0.9 mm
Chemical
Resistant:
56-day immersion durability in deionised water, chlorinated (bleach) and detergent solutions: designed to conform to AS/NZS 4858 (manufacturer classification; accredited verification testing programmed)
Full Cure:
Chemical Base:
Butyl rubber (isobutylene-isoprene rubber, IIR)
Cure Mechanism:
Tear Propagation
Resistance:
22.0 kN/m minimum (ASTM D624, typical)
Service
Temperature:
−25°C to +80°C
Solids Content:
Bond Strength:
Density:
Compressive
Strength:
Flow:
Acceptance of Cyclic Movement:
Dimensional Stability:
Control Elongation at Break:
Control Tensile Strength:
4.0 MPa minimum (ASTM D412, typical)
Water Immersion Elongation at Break:
Water Immersion Tensile Strength:
Detergent Immersion Elongation at Break:
Detergent Immersion Tensile Strength:
Heat Aging Elongation at Break:
Heat Aging Tensile Strength:
Field Seam Strength:
Temperature Resistance:
Water Vapour Transmission
Water Vapour Transmission:
0.3 g/m²/24 h maximum (ASTM E96, typical)
Application Method:
VOC Content:
Mixing Ratio:
Viscosity:
Storage Temperature:
Flash Point:
UV Resistance:
Hydrostatic Pressure Resistance:
Water Vapour Transmission Rate (WVTR):
Abrasion Resistance:
Bacterial/Algae Resistance:
Application Time:
Environmental Impact:
Packaging Sizes:
Hardness:
60–70 IRHD (ASTM D1415, typical)
Adhesion to Substrate:
Appearance After Curing:
Clean-up Requirements:
Certification Standards:
calculator
Coverage Calculator.
Based on a manufacturers average recommended coverage of Roll gross area 28 m²; effective coverage 27.2 m² per roll (1.36 m effective width x 20 m, after 40 mm welded side lap); practical coverage approximately 25–26 m² per roll
Required:
NaN
pdfs
Product Documentation.
Safety Data Sheet 2 (PDF Download)
Compliance Testing Report 1 (PDF Download)
Compliance Testing Report 2 (PDF Download)
Compliance Testing Report 3 (PDF Download)
Low VOC Certificate (PDF Download)
Product How To Guide (PDF Download)
Technical Drawings (PDF Download)
3d
Application Model


Available in (sizes)
1.4 m x 20 m x 0.9 mm roll (28 m² gross)
Need to Know More?
Got a question about ACTFLEX 900R? Our technical team can help with specification, surface prep, coverage and compatibility.
Call (02) 8021 3517
Email info@forspec.com.au